DMP Electronics Security Command 690 Manual de usuario descargar pdf (Pagina 2)

Special SECURITY COMMAND Messages

ENTER CODE:- This message will be displayed when the

SECURITY COMMAND is requesting a code number. Code

numbers are needed for arming, disarming, and many of the various

system options. When you press the SECURITY COMMAND keys

to enter your code number the numbers you enter will not be

displayed. Instead a * will be displayed for each digit. This is to keep

other people from seeing your code number when you enter it.

Always press COMMAND after you complete the entry of your code

number.

TRY AGAIN This message is displayed when a code

number is entered the first time which does not exist in the alarm

system memory.

INVALID CODE This message is displayed when a code

number is entered a second time which does not exist in the alarm

system memory.

INVALID TIME This message is displayed when a level 1 or

2 code number is entered outside permanent or temporary sched-

ules. Level 1 or 2 codes will function only during a permanent or

temporary schedule.

This message is displayed when there is an

electronic failure in your alarm system. You should contact your

SERVICE REQUIRED

alarm dealer if this message is ever displayed.

Special SECURITY COMMAND Tones

Keystroke tone: Short beep. This short beep is emitted each time

a key is pressed on the SECURITY COMMAND.

Prewarn tone: Pulsed tone, one second on, one second off,

continuous. This tone is emitted after an entry delay door is opened

to remind you to disarm your burglary system.

Monitor tone: Pulsed tone, one second on then off, one pulse only.

This tone is emitted when using the loop monitor option. The tone

will be emitted every time the loop is displayed in the alert condition.

Trouble tone: Steady tone, always on. When using the Status

Display option this tone will be emitted for any fire or system trouble

SYSTEM ARMING FOR ALL/PERIMETER SYSTEM

Area Assignment: Your burglary alarm system has been divided

into two separate areas. Interior loops like motion detectors, inside

doors, etc., have been assigned to the interior area. Perimeter loops

like windows, outside doors, etc., have been assigned to the

perimeter area. The specific loop names and their area assignment

are listed below for easy reference.

Interior area Perimeter area

Loop Name Loop Name

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

___ __________________________ ___

__________________________

All or Perimeter: When arming your system you may arm only the

perimeter area if you are remaining inside, or arm both areas if you

are leaving. The use of a code number for system arming is optional.

This option is programmed during system installation.

Bypassing: After you have made your arming selection and have

entered your code number, if required, the SECURITY COMMAND

will display any loops which have been bypassed prior to arming.

This is for your information only. They will remain bypassed until

disarmed or reset using the Bypass Loops menu option. Any 24

hour loops which are in a bad condition will also be displayed.

The system will then check to see that all doors and windows which

will be armed are closed and that any motion detectors, etc., are set

properly. If no problems exist the system will be armed. If a problem

does exist on one or more loops the SECURITY COMMAND will

display the problems and allow you to bypass those loops. If the

problem can be corrected by simply closing a door or window you

should not bypass. You should correct the problems and repeat the

arming procedure. If the loop or loops are in some way damaged and

cannot be corrected they may be bypassed. Bypassing a loop

means it will be ignored while the system is armed. A code number

may be required to bypass. This is optional and is programmed

during system installation.

Armed Message: After all loops are bypassed or corrected the

system will be armed. The SECURITY COMMAND will display the

“SYSTEM ON” message if only the perimeter is armed or “ALL

SYSTEM ON” if both have been armed. The display will then show

you the exit delay. Any exit loops will not be armed until the delay

expires. All other non-exit loops are armed immediately.

One Moment Message: Your system may be programmed to wait

for the transmission of the arming signal to the central station

receiver before displaying the Armed Message. This is to ensure

that your phone lines are working properly. While the system is

waiting for the transmission the display will read “ONE MOMENT...”.

If the test is okay the Armed Message will be displayed. If the test

1 2 3 4 5 6 7 ... 16 17

Comentarios a estos manuales

Sin comentarios

Feiyu tech FY-901 Instrukcja Użytkownika (3 strony)

Marka: Feiyu-tech | Kategoria: Accessories communication | Rozmiar: 0.54 MB |

Spis treści

POINT ARROW FORWARD

(TOWARDS FLIGHT

DIRECTION)

X-Type Layout

Cross Type Layout

Więcej produktów i instrukcji dla Akcesoria komunikacja Feiyu-tech

Modele	Rodzaj dokumentu
FY-30A	Instrukcja Użytkownika FeiYu Tech FY-30A User Manual, 13 strony
FY-30A	Instrukcja Użytkownika FeiYu Tech FY-30A User Manual, 4 strony
FY-31AP	Instrukcja Użytkownika FeiYu Tech FY-31AP User Manual, 7 strony
FY-31AP	Instrukcja Użytkownika FeiYu Tech FY-31AP User Manual, 8 strony
FY-AHRS-2000B	Instrukcja Użytkownika FeiYu Tech FY-AHRS-2000B User Manual, 14 strony
FY-AHRS-2000B	Instrukcja Użytkownika FeiYu Tech FY-AHRS-2000B User Manual, 12 strony
Hornet-OSD	Instrukcja Użytkownika FeiYu Tech Hornet-OSD User Manual, 2 strony
FY-606 Data Radio	Instrukcja Użytkownika FeiYu Tech FY-606 Data Radio User Manual, 2 strony
FY-91Q	Instrukcja Użytkownika FeiYu Tech FY-91Q User Manual, 4 strony
FY-21AP	Instrukcja Użytkownika FeiYu Tech FY-21AP User Manual, 5 strony
FY-91Q	Instrukcja Użytkownika FeiYu Tech FY-91Q User Manual, 27 strony
FY-3ZT	Instrukcja Użytkownika FeiYu Tech FY-3ZT User Manual, 57 strony
FY-ARHS-1200A	Instrukcja Użytkownika FeiYu Tech FY-ARHS-1200A User Manual, 12 strony
FY-AHRS-1200B	Instrukcja Użytkownika FeiYu Tech FY-AHRS-1200B User Manual, 8 strony
FY-Y6	Instrukcja Użytkownika FeiYu Tech FY-Y6 User Manual, 7 strony
FY-X4	Instrukcja Użytkownika FeiYu Tech FY-X4 User Manual, 7 strony
FY-AP117	Instrukcja Użytkownika FeiYu Tech FY-AP117 User Manual, 1 strony
FY-90Q	Instrukcja Użytkownika FeiYu Tech FY-90Q User Manual, 2 strony
FY-602 Data Radio	Instrukcja Użytkownika FeiYu Tech FY-602 Data Radio User Manual, 7 strony
FY-20A	Instrukcja Użytkownika FeiYu Tech FY-20A User Manual, 3 strony

DMP Electronics Security Command 690 Manual de usuario Pagina 2

Comentarios a estos manuales

Feiyu-tech FY-901 podręczniki

Feiyu tech FY-901 Instrukcja Użytkownika (3 strony)

Spis treści

Więcej produktów i instrukcji dla Akcesoria komunikacja Feiyu-tech

DMP Electronics Security Command 690 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Teclados numéricos DMP Electronics Security Command 690

Feiyu-tech FY-901 podręczniki

Feiyu tech FY-901 Instrukcja Użytkownika (3 strony)

Spis treści

Więcej produktów i instrukcji dla Akcesoria komunikacja Feiyu-tech