DMP Electronics SCS2 Manual de usuario Pagina 1

JTAG-Booster forAMD ÉlanSC520P.O. Box 1103 l D-79200 Breisach, GermanyKueferstrasse 8 l D-79206 Breisach, Germany(+49 (7667) 908-0 l Fax +49 (7667) 90

JTAG-Booster for AMD ÉlanSC52010 JTAGEL5d.doc1.5. Error Messages• 80386 or greater requiredThe JTAG-BOOSTER does not work on a 8088/8086 or a 80286 pl

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 11• illegal function:The first parameter of the command line must be a valid function. Seechapter 2 “JTAGE

JTAG-Booster for AMD ÉlanSC52012 JTAGEL5d.doc• missing option /I2CCLK=Some functions need the option /I2CCLK= to be defined.• missing option /I2

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 13• Pins specified with /I2CCLK= and /I2CDATI= must have differentcontrol cellsThe pin specified with

JTAG-Booster for AMD ÉlanSC52014 JTAGEL5d.doc1.6. Initialization file JTAGEL5.INIThis file is used to set the CPU signals for input/output. In case of

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 15MA1 Out,Lo //MA0 Out,Lo //// Group B: All pins in this group must be set to the same direction//

JTAG-Booster for AMD ÉlanSC52016 JTAGEL5d.docMECC2 Inp //MECC1 Inp //MECC0 Inp //// Group C: All pins in this group must be set to the same direction/

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 17AD25 Inp //AD24 Inp //AD23 Inp //AD22 Inp //AD21 Inp //AD20 Inp //AD19 Inp //AD18 Inp //AD17 Inp //AD16 I

JTAG-Booster for AMD ÉlanSC52018 JTAGEL5d.docGPA22 Out,Lo // = RSTLD7 config switchGPA21 Out,Lo // = RSTLD6 config switchGPA20 Out,Lo // = RSTLD5 conf

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 19GPD3 Inp //GPD2 Inp //GPD1 Inp //GPD0 Inp //// The direction of each following pin can be set independent

JTAG-Booster for AMD ÉlanSC5202 JTAGEL5d.docCopyright  1995..2002:FS FORTH-SYSTEME GmbHPostfach 1103, D-79200 Breisach, GermanyRelease of Document:

JTAG-Booster for AMD ÉlanSC52020 JTAGEL5d.docPAR Inp //PERR# Inp //FRAME# Inp //TRDY# Inp //IRDY# Inp //STOP# Inp //DEVSEL# Inp //PIO27 Inp // = GPCS0

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 21DATASTRB Out,Lo //CPUACT Out,Lo //PITOUT2 Out,Lo //PITGATE2 Inp //TMRIN1 Inp //TMRIN0 Inp //TMROUT1 Out,L

JTAG-Booster for AMD ÉlanSC52022 JTAGEL5d.doc1.7. Supported flash devicesThe following types could be used with the /DEVICE= option:AM29F010 : AMD 29F

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 23* AM29LV800BB : AMD 29LV800B (3.3V, byte mode)AM29LV800TW : AMD 29LV800T (3.3V, word mode)* AM29LV800TB :

JTAG-Booster for AMD ÉlanSC52024 JTAGEL5d.doc* I28F004B : Intel 28F004B* I28F004T : Intel 28F004T* I28F400B3B : Intel 28F400B3B Boot Block Smart3 Bott

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 25* MBM29LV200BW : Fujitsu 29LV200B (3.3V, word mode)* MBM29LV200BB : Fujitsu 29LV200B (3.3V, byte mode)* M

JTAG-Booster for AMD ÉlanSC52026 JTAGEL5d.doc* MBM29F160BB*2 : Dual Fujitsu 29LV160B (byte mode)* MBM29F160TB*2 : Dual Fujitsu 29LV160T (byte mode)* M

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 272. JTAGEL5 Parameter DescriptionWhen you start JTAGEL5.EXE without any parameters the following help scr

JTAG-Booster for AMD ÉlanSC52028 JTAGEL5d.docThe following options are valid for most functions:/DRIVER=x with x = 1,2,3,4A driver for the interface t

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 29/WATCH=With the option /WATCH= a pin can be specified, which is toggled twice persecond, while the progra

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 3Table of Contents1. General...

JTAG-Booster for AMD ÉlanSC52030 JTAGEL5d.doc2.1. Programming a Flash DeviceUsage: JTAGEL5 /P filename [optionlist]The specified file is programmed

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 31/TOPIf the option /TOP is used the option /OFFSET= specifies the address where theprogramming ends (plus

JTAG-Booster for AMD ÉlanSC52032 JTAGEL5d.doc/BOOTCS /ROMCS1 /ROMCS2This options may be used to specify one or more chip select signals to the flash

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 33Examples:JTAGEL5 /P ROMDOS.ROM /VERIFY /L=20000 /TOPThis example programs up to 128 Kbytes of the fi

JTAG-Booster for AMD ÉlanSC52034 JTAGEL5d.doc2.2. Read a Flash Device to fileUsage: JTAGEL5 /R filename [optionlist]The contents of a flash device

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 35/BOOTCS /ROMCS1 /ROMCS2 /NOCSSee function /P (Chapter 2.1)/8BIT /16BITSee function /P (Chapter 2.1)

JTAG-Booster for AMD ÉlanSC52036 JTAGEL5d.doc2.3. Verify a Flash Device with fileUsage: JTAGEL5 /V filename [optionlist]The contents of a flash dev

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 37/8BIT /16BITSee function /P (Chapter 2.1)/32L /32HSee function /P (Chapter 2.1)/MBUSSee function /P (Ch

JTAG-Booster for AMD ÉlanSC52038 JTAGEL5d.doc2.4. Dump target memoryUsage: JTAGEL5 /DUMP [optionlist]A Hex-Dump of the target memory is printed on t

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 392.5. Program an I²C-DeviceUsage: JTAGEL5 /PI2C filename [optionlist]The specified file is programmed t

JTAG-Booster for AMD ÉlanSC5204 JTAGEL5d.doc1. GeneralThe program JTAGEL5 uses the JTAG port of the AMD ÉlanSC520 embeddedmicroprocessor in conjuncti

JTAG-Booster for AMD ÉlanSC52040 JTAGEL5d.doc/LENGTH=hhhhhhThe number of programmed bytes may be limited to LENGTH. If no LENGTH isspecified the whole

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 412.6. Read an I²C-Device to fileUsage: JTAGEL5 /RI2C filename /L=hhhhhh [optionlist]The contents of a

JTAG-Booster for AMD ÉlanSC52042 JTAGEL5d.docExample: JTAGEL5 /RI2C EEPROM.CFG /I2CCLK=PIO31 /I2CDAT=PIO30/L=100This example reads 256 bytes from

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 432.7. Verify an I²C-Device with fileUsage: JTAGEL5 /VI2C filename [optionlist]The contents of a I²C-Dev

JTAG-Booster for AMD ÉlanSC52044 JTAGEL5d.docExample: JTAGEL5 /VI2C EEPROM.CFG /I2CCLK=PIO31 /I2CDAT=PIO30This example verifies 256 bytes from a s

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 452.8. Dump an I²C-DeviceUsage: JTAGEL5 /DUMPI2C [optionlist]A Hex-Dump of a I²C-Device is printed on the

JTAG-Booster for AMD ÉlanSC52046 JTAGEL5d.doc2.9. Toggle CPU pinsUsage: JTAGEL5 /BLINK /PIN=pinname [optionlist]This command allows to test the har

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 472.10. Polling CPU pinsUsage: JTAGEL5 /PIN? /PIN=pinname [optionlist]This command allows to test the h

JTAG-Booster for AMD ÉlanSC52048 JTAGEL5d.doc2.11. Polling CPU pins while the CPU is runningUsage: JTAGEL5 /SAMPLE /PIN=pinname [optionlist]This c

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 492.12. List of supported Flash DevicesUsage: JTAGEL5 /LIST [optionlist]This command lists all supported

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 51.2. Connecting your PC to the target systemThe JTAG-Booster can be plugged into standard parallel ports (

JTAG-Booster for AMD ÉlanSC52050 JTAGEL5d.doc3. Implementation InformationThis chapter summarizes some information about the implementation of theJTA

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Digi International: FS-931

JTAG-Booster for AMD ÉlanSC5206 JTAGEL5d.docThe utility is started with the general command line format:JTAGEL5 /function [filename] [/option_1] ... [

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 71.3. First ExampleIn the following simple example it is assumed that the JTAG-Booster is connectedto LPT1

JTAG-Booster for AMD ÉlanSC5208 JTAGEL5d.docErase Time : 1.1 secProgramming Time : 121.2 sec(1) The initialization file JTAGEL5.INI was found in th

JTAG-Booster for AMD ÉlanSC520JTAGEL5d.doc 91.4. Trouble ShootingAvoid long distances between your Host-PC and the target. If you are usingstandard pa