Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 28)

XR500 Series Canadian Programming Guide Digital Monitoring Products

DEVICE SETUP

6.13

OVERRIDE NO YES

Schedule Override

UsethisoptiontoallowdoorON/OFFschedulestobeoverriddenbythearmed

condition of the system. Selecting YES causes the on time for a door schedule to be

ignored when all areas assigned to Access Areas for this device are armed. Should

any area become disarmed after the door schedule on time, the device output turns

on. A door output which is on during a disarmed period automatically turns off when

all access areas assigned to the device become armed, even if the scheduled off

time has not been reached. This feature can be used to keep doors locked when a

factory opens late, or is forced to close early, due to a snow storm or other cause.

Select NO to allow door schedules to operate independent of system armed status.

Note: When OVERRIDE is YES and there are no areas programmed in ACCESS AREAS,

the door schedule for that device does not work. Either set OVERRIDE to NO or

enter an area number in ACCESS AREAS.

6.13 Auto Force Arm Device?

Select YES to have all Display Areas assigned to this keypad automatically arm and

force arm faulted zones at arming. The user is not prompted to select areas to

arm or force arm faulted zones after choosing ARM at the keypad. If Closing Code

is programmed as YES, only the matching areas between the Display Areas and

the User Code’s authorized areas arm. Also, when YES is selected, the user is not

prompted to select areas to disarm after entering a code at Entry Delay or after

choosing Disarm at the keypad. All matching areas assigned to the User Code and to

this keypad are automatically disarmed. When NO is selected, the user is prompted

toselectareas(ALLNOYES)andchoosetoforcearmorbypassatarmingand

disarming. Default is NO.

6.15 Door Real-Time Status?

Select YES tohavereal-timedoorstatusmessagessenttoPCLogreportingandEntré

reporting for this device. Messages are sent anytime the panel turns the door relay on or

off. Default is NO.

6.16 Send Door Forced Message?

Select YES tohavethepanelsendareal-timedoorstatusmessageofForcedOpen(FO)

toPCLogreportingandEntréreportingwhenthedoorrelayisoff,butthedoorzonehas

transitioned from its normal state. Default is NO.

6.17 Program 734/734N Options

Select YES toprograma734/734N/

734N-WiFi

Wiegand Interface Module. The options

displayedfora734ora734Narethesame.

 Toprograma734,theDevicetypemustbesettoDOORandtheDeviceCommunication

Type must be set to KPD BUS.

Toprogramthe734N/

734N-WiFi

, the Device Type must be set to DOOR and the Device

Communication Type must be set to NETWORK.

6.18.1 Activate Zone 2 Bypass

Select YES to activate the Bypass option.

Selecting NO allows standard zone operation on Zone 2 and displays the ACTIVATE

ZONE 3 REX option. Default setting is NO.

Ifthedoorbeingreleasedbythe734/734N

734N-WiFi

moduleisprotected(contact

installed),youcanprovideaprogrammableBypassentry/exittimerbyconnecting

itscontactwiringtothe734/734N

734N-WiFi

moduleZone2.Whentheon-board

Form C relay activates and the user opens the door connected to Zone 2, the zone is

bypassed for the number of seconds programmed in ZONE 2 BYPASS TIME allowing the

usertoenter/exit.

IfZone2doesnotrestore(doorclosed)withintheprogrammedtimeminusten

seconds,the734/734N

734N-WiFi

piezo pulses during the last ten seconds. If Zone

2 restores prior to the end of the programmed time, the piezo silences. If the zone

doesnotrestorebeforetheprogrammedtime,the734/734N

734N-WiFi

ends the

bypass and indicates the open or short zone condition to the panel.

6.18.2

ZONE 2 BYPASS

TIME: 40

Zone 2 Bypass Time

Enter the number of Bypass seconds to elapse before the Bypass timer expires.

Range is from 20 to 250 seconds. Press any top row select key to enter the number

ofseconds.Ifthedoorremainsopenwhenthetimerexpiresazoneopen/shortis

sent to the panel for Zone 2. The default is 40 seconds.

AUTO FORCE ARM

DEVICE? NO YES

DOOR REAL-TIME

STATUS? NO YES

SEND DOOR FORCED

MESSAGE? NO YES

PROGRAM 734

OPTIONS? NO YES

ACTIVATE ZONE 2

BYPASS? NO YES

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500