Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 36)

XR500 Series Canadian Programming Guide Digital Monitoring Products

SYSTEM OPTIONS

System Options

9.1

SYSTEM OPTIONS

System Options

Thissectionallowsyoutoselectsystem-wideparameters.

9.2

SYSTEM: AREA

System

This option allows you to program how the areas operate for arming and disarming.

The options you can choose are listed below:

AREA A/P H/A GST

AREA - All 32 areas can be programmed and operated independently.

ALL/PERIMETER - Area 1 is the Perimeter and Area 2 is the Interior.

HOME/SLEEP/AWAY - Area 1 is the Perimeter, Area 2 is the Interior, and Area 3 is the

Bedrooms.WiththeHOME/SLEEP/AWAYoption,theusercan:

1. Select HOME to arm just the perimeter.

2.SelectSLEEPtoarmtheperimeterandinterior(nonbedroomareas).

3. Select AWAY to arm all three areas.

Note:AHome/Sleep/Awaysystemcanbeconguredtouseallthreeareasor

only use the Home and Away areas.

HOME/SLEEP/AWAY WITH GUEST- This allows the alarm system to be divided into a

mainhouseHOME/SLEEP/AWAYsystemandtwootherguesthousesthatalsoareset

upasHOME/SLEEP/AWAYsystems.

Areas 1, 2, and 3 are the Perimeter, Interior, and Bedrooms for the Main house

system.Areas4,5,and6arethePerimeter,Interior,andBedroomsfortheGuest

1housesystem.Areas7,8,and9arethePerimeter,Interior,andBedroomsfor

theGuest2housesystem.Theseareasareautomaticallyassignedpersystemand

cannot be changed. See Display Areas in Device Setup to assign keypads to a system.

Zones are assigned to a system by assigning the system’s area numbers to the zone in

Zone Information programming.

WheneitherAll/PerimeterorHome/Sleep/Awayisselected,theareanamesare

automaticallyassignedandcannotbemodied.

Note:Areas3-32inanAll/Perimetersystem,areas4-32inaHome/Sleep/Away

system,andareas10-32inaHome/Sleep/AwaywithGuestsystemarenotavailable

for use and are initialized.

9.3

INST ARM NO YES

Instant Arming

When YES is selected, the arming keypad displays INSTANT for selection during the exit

countdown delay when arming fewer than all areas of the system. At the time instant

arming is selected, any entry and exit delays programmed for the areas being armed

are ignored. The entry delay for previously armed areas is not affected by instant

arming. When NO is selected, INSTANT does not display during arming. Default is NO

foranAreaSystem,andYESforanAll/PerimeterorHome/Sleep/Awaysystem.

9.4

CLS WAIT NO YES

Closing Wait

When YES is selected, the keypad displays ONE MOMENT... while waiting for

anacknowledgementfromthereceiverbeforearmingtheselectedarea(s)and

performingaBellTest(ifselected).ExitdelaysbeginaftertheClosingWait.

Opening/ClosingreportsmustbeYEStoenableClosingWait.

9.5

ENTRY DLY 2: 60

ENTRY DLY 3: 90

ENTRY DLY 1: 30

ENTRY DLY 4: 120

Entry Delay 1

Enter the Entry Delay time for all Exit type zones programmed to use Entry Delay 1.

When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding.

AllkeypadsprogrammedtoprewarnforthatzonedisplayENTERCODE:-andthe

nameofthezonecausingtheentrydelay.Whentherstdigitofacodeisentered,

the prewarn tone stops at that keypad. If an invalid code is entered, the prewarn

tone begins sounding again. The area must be disarmed before the delay expires

or an alarm report is sent to the receiver and an alarm sounds. All zones in that

area are delayed along with the Exit zone. Entry Delay times can be from 30 to 250

seconds. Repeat the above for each entry delay being used in the system.

Note:SpecicExitErroroperationisbasedontheEntryDelayused(1-4)withanEX

type zone. See Exit Delay.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 36

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500