Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 72)

XR500 Series Canadian Programming Guide Digital Monitoring Products

APPENDIX

Appendix

23.1 False Alarm Reduction

System Recently Armed report

TheSystemRecentlyArmedreport(S78)issenttothereceiverwhenaburglaryzonegoesintoalarm

within two minutes of the system being armed.

23.2 Diagnostics function

The XR500 Series Canadian panel contains a Diagnostics function that allows you to test the communication

integrityoftheLX-Bus™,identifyindividualzones,andalsodisplaythepresentelectricalstateofany

zone. The Diagnostics function also allows you to test the integrity of the cellular communication, cellular

signal, and email communication. To use Diagnostics, reset the panel, enter the Diagnostics code 2313

(DIAG),andpressCOMMAND.

Test LX-Bus

TherstDiagnosticfunctionyoudisplayedis:TEST LX-BUS. This function allows you to test the ability of

the481,462N,462P,463C,463Gand472InterfaceCardstocommunicatewithzoneandoutputexpander

modulesconnectedtotheirLX-Buscircuits.

To continue, press any top row Select key. The keypad displays LX-BUS:. Using the digit keys, enter the

LX-Busnumber,1to5,totestthatLX-Buscircuit.ThekeypadnowdisplaysADDRESS: -.Entera2-digit

LX-BusdeviceaddressandpressCOMMAND.WhentestingLX-Busdevices,enteronlytheaddressesto

which the modules have been set.

Important Note: Adeviceaddressisnotthesameasazonenumber.Ifyouaretesting714or715Zone

ExpanderModules,whicheachcontainfourzones,thedeviceaddressistherstzonenumber.Whenthe

panelpollsa714ontheLX-Bus,itrecognizesitasafourzonedeviceanddoesnotpolltheremaining

threezones.The714moduleinternallypollstheremainingzonesandtransmitsanystatuschangestothe

panel.ThisgreatlyreducestheamountoftimeittakesthepaneltopollallLX-Busdevices.

The keypad next displays TESTING . . . STOP during the device testing. At any time, you can Select

STOP to end polling. The panel records the number of no responses from the device. If all polls are

received back by the panel correctly, the keypad displays 00000/65535 FAIL.

If one or more polling attempts fail, the keypad displays * * * * */65535 FAILwiththe*representingthe

number of failed polling attempts. A display of 65535/65535 FAIL indicates a problem with the interface

cardoritsLX-Buswiringsuchasabadorbrokenwire,harnessnotproperlyconnected,orexcessivenoise

or distance. It can also mean that a zone number was entered that did not match a device address. Press

the Back Arrow key to enter a new device address or press COMMAND to exit the TEST LX-BUS.

Zone Finder

The second Diagnostic function is the Zone Finder. Press COMMAND to display ZONE FINDER. This function

allowsyoutoidentifyindividualzonesondevicesconnectedtotheLX-Busofaninterfacecard,thepanel,

or any zones on the keypad data bus. To use ZONE FINDER, press any top row Select key. The display

changes to FAULT ZONE. The next zone on the system that changes from a normal to an open or shorted

state is displayed as ZONE NO: * * *. To continue, press the Back Arrow key.

Zone State

Press the COMMAND to display the third Diagnostic function: ZONE STATE. This function allows you to

enteranyzonenumberandcheckitscurrentelectricalstate(Normal,Open,orShorted).PressanySelect

key. The display changes to ZONE NUMBER: _ . Enter in the zone number you want to check and press

COMMAND. The panel displays the current state of the zone as NRML(normal),OPEN, or SHORT.

LX-Bus Status

The fourth Diagnostic function is the LX-BUS STATUS. This function allows the panel to poll all devices

connectedtotheLX-BusofaninterfacecardandcheckforanyOverlapped,Missing,orExtraaddresses.

Below is a description of each status item:

Overlap -Anoverlapoccurswhenonedeviceaddressisthesameasanyofthelastthreezonesonanother

714or715.Theoverlapfeaturecannotdeterminewhentwodeviceshavethesameaddress.

Example: Model714Address00=Zones500501502503,andtheModel711Address02=Zone502.

Zone502wouldreportasanOverlapbecauseboththe714and711havedevicessetto502.

Missing -Amissingoccurswhenazonebetween500and999hasbeenprogrammedinZONE INFORMATION

andnodevicewiththatzoneaddresshasbeeninstalledontheLX-Bus.Tocorrecttheproblem,check

your zone programming and zone expansion module addressing.

Extra -AdeviceisinstalledontheLX-Busbutnoneofitszonesareprogrammedintothesystem.

MAC Address

ShortforMediaAccessControladdress.Thishardwareaddressuniquelyidentieseachnetworknode.Not

to be confused with an IP address, which is assignable. In the Diagnostics function, the MAC address is the

panelon-boardnetworkhardwareaddress.PressanytoprowSelectkeytodisplaythepanelMACaddress.

Press the COMMAND key to view the next prompt.

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 72

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500