Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 76)

XR500 Series Canadian Programming Guide Digital Monitoring Products

APPENDIX

END - SelectENDtostoptheWalkTest.WhentheWalkTestendsora20-minute

time-outexpires,analSensorResetoccurs.TheSystemTestEndmessageis

sent to the receiver along with Verify and Fail messages for each zone under test.

Faulted zones then display on the keypad.

CKIN:XXX/ZZZ END

Trip Counter For DMP Wireless Check-in Test (WLS)

Displays the number of wireless zones that automatically communicate a supervision

check-inmessage.

• Thenumberofzonesthatcheckin.(XXXintheexample).

• Thetotalnumberofwirelesszonesprogrammedforsupervisionthatshould

checkin.(ZZZintheexample).

END -SelectENDtostoptheWirelessCheck-inTest.Whenthetestendsor

a20-minutetime-outexpires,normalwirelesszoneprocessingreturns.If

alltransmitterscheck-in,bothnumbersmatchwithinthree(3)minutes.Ifa

transmitterhasmultiplezones(1101,1114,etc.),allzonesareincludedinthe

counts. Failed wireless zones display on the keypad.

TEST END WARNING

Test End Warning

Whenveminutesremainonthe20minuteWalkTesttimer,thekeypaddisplays

TESTENDWARNING.Ifnoadditionaltestzonetripsoccur,thetestendsandanal

Sensor Reset automatically occurs. The System Test End message is sent to the

receiver along with Verify and Fail messages for each zone under Walk test. Faulted

zones then display on the keypad.

Note: Key fobs do not send failure messages in order to prevent functioning key fobs

thatarenotpresentatthetimeofthetestfrombeingreportedasMISSING.

Failed Zones Display

ZONE: 10 -FAIL

Foreachzonethatdidnottrip(failed)atleastonceduringtheWalkTest,all

keypads with matching Area Display programming display the zone name and number

andbuzzforonesecond.Anyselected(*FI*PN*SV)24-hourzonethatisfaultedat

the end of the Walk Test displays a trouble condition for that zone regardless of the

message programmed for the open or short condition of the zone and a zone trouble

is sent to the receiver. Press the COMMAND key to display the next failed zone.

Note:FortheWirelessCheck-inTest,failedwirelesszonesdisplayonlyonthe

keypad.ZoneVerify/Failreportsarenotsenttothecentralstationreceiverforthe

wirelesscheck-intest.

Local Printer for Walk Test

When the Walk Test is completed, a Verify or Fail message for each zone tested prints to the local printer.

The Walk Test messages printing is enabled through Printer Reports programming.

Note: If ENHANCED ZONE TEST is selected as YES, the Verify messages are printed at the time the zone

trip occurs and not printed at the test end.

23.5 Keypad Speaker Operation

WhenusingLCDKeypads,thepanelprovidesdistinctspeakertonesfromthekeypadforFire,Burglary,

Zone Monitor, and Prewarn events. The list below details the conditions under which the speaker is turned

on and off for each event.

Fire On-FirezonealarmandBellOutputorFireBellOutputisON.

Off -AlarmSilence.

Burglary On -BurglaryzonealarmandBellOutputorBurglaryBellOutputisON.

Off-AlarmSilence.

Zone Monitor On-Onetimeonlywhenamonitoredzoneistripped.

Off-Afteronetone.

Prewarn On-DuringEntryDelay.

Off-WhenEntryDelayexpires.

1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 76

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500