Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 60)

XR500 Series Canadian Programming Guide Digital Monitoring Products

ZONE INFORMATION

When the zone changes from normal to shorted, the programmed areas toggle between

the armed or disarmed condition using the Style programming below. When restored to

normal,noactionoccurs.Whenthezoneisopenedfromanormal(disarmed)state,a

troubleisreported.Whenopenedfromashorted(armed)state,analarmisreported

andthezoneisdisableduntilyoudisarmthearea(s)fromeitherakeypadorRemote

Link™computer.

Tovisuallyindicatethearmedstateofthearea(s),youcanassignanArmedOutput

toindividualareasanduseremoteLEDsatthekeyswitch.TheLEDturnsonoroffto

indicatetotheuserthearmedstateofthearea(s).

ARM AREAS: PERIM

InanAll/PerimeterorHome/Sleep/Awaysystem,thisoptionspeciestheareasto

bearmedbytheArmingTypezone.ForAll/Perimetersystems,choosePERIMorALL,

forHome/Sleep/AwayorHome/Awaysystems,chooseHOME,SLEEP,orAWAY.

PERIM ALL

Perimeter/All-SpecifywhetherthearmingzonearmsjustthePerimeter(PERIM)or

thePerimeterandInteriorareas(ALL)forAll/Perimetersystems.Whendisarming,

all areas are disarmed.

HOME SLEEP AWAY

Home/Sleep/Away-SpecifywhetherthearmingzonearmsthePerimeter(HOME),

thePerimeterandInterior(SLEEP),orallthreeareas(AWAY).Whendisarming,all

areas are disarmed.

Arming Zone Operation

IfanybadzonesarepresentwhentheArmingzoneisshorted,theLEDdelays

lightingfor5seconds.Ifduringthe5-seconddelaytheArmingzoneisshorted

again no arming takes place. If 5 seconds expire without the zone shorting again

or restoring to normal, the areas arm and bad zones are force armed. To allow bad

zones to be force armed, the Any Bypass option must be set to YES. If Any Bypass

optionissettoNO,armingdoesnotoccur.SeetheAreaInformation-AnyBypass

section. A priority zone cannot be force armed.

19.8

STYLE:

Style

Thisoptionspeciesthestyleforthearming/disarmingoperation.Thedefaultstyle

isTGL(toggle).PressanySelectkeytodisplaytheSTYLEoptions.Toviewmore

style options press the COMMAND key.

TGL ARM DIS STEP

TGL (Toggle) - When the zone changes from normal to shorted, the programmed

areas toggle between the armed or disarmed condition. When restored to normal,

noactionoccurs.Whenthezoneopensfromanormal(disarmed)state,atroubleis

reported.Whenopenedfromashorted(armed)state,analarmisreportedandthe

zoneisdisableduntilyoudisarmthearea(s)fromeitherakeypadorRemoteLink.

ARM - When the zone is shorted, the programmed areas are armed. When restored to

normal,noactionoccurs.Whenthezoneisopenedfromanormal(disarmed)state,a

troubleisreported.Whenopenedfromashorted(armed)state,analarmisreported.

DIS (Disarm) - When programmed, a short disarms the programmed areas. When

restored to normal, no action occurs. When the zone is opened from a normal

(disarmed)state,atroubleisreported.

STEP - A short arms the areas and beeps the keypads once. A normal condition

causes no action. An open condition disarms the programmed areas and beep the

keypads for one second.

Note: This arming style is designed for wireless arming pendants. When using an

arming/disarmingkeyswitchlocatethekeyswitchwithintheprotectedarea.

MNT

MNT (Maintain) - When the zone is shorted, the programmed areas are armed.

When restored to normal, the programmed areas are disarmed and any alarm bells

aresilenced.Whenthezoneisopenedfromanormal(disarmed)state,atrouble

isreported.Ifopenedfromashorted(armed)state,analarmisreportedandthe

zoneisdisableduntilyoudisarmthearea(s)fromeitherakeypadorRemoteLink.

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 60

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500