Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 52)

XR500 Series Canadian Programming Guide Digital Monitoring Products

PC LOG REPORTS

PC Log Reports

17.1

PC LOG REPORTS

PC Log Reports

ThissectionallowsyoutoprogramthetypesofPCLogReportsthepanelsends

throughthe462NNetworkInterfaceCardorthroughtheJ21SerialConnectordirectly

on the XR500 Series Canadian panel. The reports include information such as the type

of activity, time and date of the activity, and user name and number. These data

reports can be accessed from a PC using the Advanced Reporting Module. See the

InstallationGuide(LT-0681CAN)fordetailedJ21setupinformationortheUser’sGuide

(LT-0683CAN)formoreinformation.

Note:ThenetworkconnectionthatsendsPCLogReportsisnotmonitoredfornetwork

trouble.ThePCLogReportsoptionshouldNOTreplacetheprimarycommunication

method or act as a backup communication method.

If there is trouble with the network connection, the panel continues to attempt to

sendthePCLogReportsuntiltheconnectionisreestablished.Thepanelthensends

the reports. A Network Trouble message is NOT sent if the connection is lost since this

reporttoolisnotdesignedtobemonitoredbyareceiver.ThePCLogReportshave

the lowest priority of panel reports sent.

Forinformationaboutthe462NcardcapabilitieswithPCLogReportsandNetwork

Communicationmethod,see462NCardExamplesintheAppendix.

Note:ThePCLogAddressStringenteredCANNOTbethesameasthatenteredin

Communication.

17.2

COMM TYPE: NONE

Communication Type

NONE NET 232

SelecttheCommunicationTypetosendthePCLogReports.DefaultisNONE.

17.3

NET IP ADDRESS

Net IP Address

ThisoptiondisplayswhentheCommunicationTypeforPCLogReportsisNET.Enter

theIPaddresscontainingupto16characters.TheNetIPAddressmustbeuniqueand

cannot be duplicated on the network. Enter all 12 digits and leave out the periods.

Forexample,enterIPaddress192.168.0.250as192168000250.Theperiodsdisplay

automatically.

17.4

NET PORT 2001

Net Port

ThisoptiondisplayswhenCommunicationTypeforPCLogReportsisNet.Enterthe

Portnumber.Validnumbersarefrom0to65535.Defaultis2001.

17.5

232 COMM PORT: O

232 Communication Port

ThisoptiondisplayswhenCommunicationTypeforPCLogReportsis232.Toenable

PCLogReports,selecteithertheon-boardconnector(O)orselectA,B,C,DorEfor

thecorrespondingslotinuseontheDMPModel462NNetworkInterfacecard.The

slots are labeled from left to right, beginning with A. Default is O.

SettheXR500SeriespanelJ23jumpertoRandbrieyresetthepanelusingtheJ16

jumpertoactivateRS-232operation.

17.6

232 SETUP:

232 Setup

ThisoptiondisplayswhenCommunicationTypeforPCLogReportsis232.Enterupto

32 characters.

17.7

ARM/DIS NO YES

Arm and Disarm Reports

Sendsarming,disarmingandLatetoCloseevents.Includestheareanumber,name

and action, the user number and name, and the time and date.

17.8

ZONE NO YES

Zone Reports

Sends changes in the status of active zones. Includes the zone number, name, type,

theaction(alarm,trouble,bypass,etc.),usernumber(ifapplicable),andareaname.

For a Walk Test, Verify and Fail messages are sent for each zone.

17.9

USR CMDS NO YES

User Command Reports

Sends user code changes, schedule changes, and door access denied events.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500