Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 29)

Digital Monitoring Products XR500 Series Canadian Programming Guide

DEVICE SETUP

6.18.3

RELOCK ON ZONE 2

CHANGE? NO YES

Relock on Zone 2 Change?

Selecting NO leaves the relay on for the door access time when Zone 2 restores.

SelectingYESturnsthe734/734N

734N-WiFi

relay off and relocks the door when

Zone 2 changes state. The default is NO.

6.18.4

ACTIVATE ZONE 3

REX? NO YES

Activate Zone 3 Request to Exit

SelectingYESactivatestheZone3RequesttoExit(REX)option.

Selecting NO allows standard zone operation on Zone 3 and displays the ACTIVATE

ONBOARD SPEAKER option. Default setting is NO.

OptionallyconnectaPIR(orothermotionsensingdevice)oramechanicalswitchto

Zone 3 to provide REX capability to the system. When Zone 3 shorts,theon-board

Form C relay activates for the programmed number of seconds. During this time,

theusercanopentheprotecteddoortostarttheprogrammedBypassentry/exit

timer. After the programmed number of seconds, the relay restores the door to its

locked state.

The734/734N

734N-WiFi

moduleprovidesabypass-onlyoptionforREXonZone3.

WhenZone3opensfromanormalstate,onlyaBypassoccurs:theon-boardrelay

doesnotactivate.Thisbypass-onlyoptionusestwomethodsofREX.TherstREX

deviceprovidestheprogrammedBypassentry/exittimer.ThesecondREXdevice,or

manual device such as a door knob, unlocks the door.

Anexampleofthebypass-onlycongurationisadoortoanofcethatislocked24

hours a day. Users pass a REX motion detector positioned by the door to begin the

programmed exit timer. Within the programmed number of seconds the user must

then manually activate a second device, such as a REX device or manual door knob,

to unlock the door. If the door is opened after the programmed number of seconds,

the zone goes into alarm

6.18.5

ZN 3 REX STRIKE

TIME: 5

Zone 3 REX Strike Time

Enter the number of REX seconds to elapse. Range is from 5 to 250 seconds. Press

any top row select key to enter the number of seconds. The default is 5 seconds.

Press the COMMAND key to move forward to the ACTIVATE ONBOARD SPEAKER option.

The Back Arrow returns to ACTIVATE ZONE 3 REX.

6.18.6

ACTIVATE ONBOARD

SPEAKER? NO YES

Activate Onboard Speaker

Select YES to enable the onboard piezo speaker for local annunciation. Select NO to

turn the piezo off for all operations. This does not affect remote annunciator open

collector(RA)operation.ThedefaultisNO.

6.18.7

CARD OPTIONS:

DMP

Card Options

Press any top row Select key to display options. Press the select key under DMP,

CUSTOMorANYtoselectthatoption.SelectDMPtoindicatethereadersendsa26-

bit DMP data string. Press the COMMAND key to display REQUIRE SITE CODE.

Note: When set to DMP, the 734/734N/734N-WiFi converts 17 bits of the 26-bit

data string into a 5-digit number.

SelectCUSTOMifusinganon-DMPcardorusercodelengthof6to10digits.

Default is DMP.

Select ANY to allow all card reads to activate the door strike relay. The door strike

relay is activated for the length of time programmed in ZN 3 REX STRIKE TIME. No

user code information is sent to the panel.

6.18.8

WIEGAND CODE

LENGTH: 26

CustomCardDenitions

Wiegand Code Length

When using a custom credential, enter the total number of bits to be received in

Wiegand code including parity bits.

PressanytoprowSelectkeytoenteranumberbetween1-255toequalthenumber

ofbits.Defaultis26bits.

Typically,anaccesscardcontainsdatabitsforasitecode,ausercode,andstart/

stop/paritybits.Thestartingpositionlocationandcodelengthmustbedetermined

andprogrammedintothe734/734N

734N-WiFi

Module.

CARD OPTIONS:

DMP CUSTOM ANY

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500