Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario descargar pdf (Pagina 62)

XR500 Series Canadian Programming Guide Digital Monitoring Products

ZONE INFORMATION

consecutive zone numbers. Default is Contact 1.

Forexample,useserialnumber08345678toprogramContact1forZone561,

Contact2forZone562,Contact3forzone563,andContact4forzone564.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

ALREADY IN USE

ZONE NUMBER: XXX

This message displays when the Contact is already programmed for another

zone. The programmed zone number displays.

ZONE INFORMATION

NORM OPN NO YES

This option only displays when EXT is selected as the Contact type. For external

devices connected to the 1101 or 1103 terminal block, select NO to use normally

closed(N/C)contacts.SelectYEStousenormallyopen(N/O)contacts.Default

is NO.

19.10.3

TRANSMITTER

SUPRVSN TIME: 240

Supervision Time

Press any top row key to select the supervision time required for the wireless

zone. Press COMMAND to accept the default time. Default is 240 minutes.

Note:RefertotheWirelessCheck-inandSupervisionTimeDenitionssection

of the Appendix for supervision information.

SELECT MINUTES:

0 3 60 240

Press the Select key under the required number of minutes. The transmitter

must check in at least once during this time or a missing condition is indicated

for that zone. 1100 Series transmitters automatically checkin based on the

supervision time selected for the wireless zone, no additional programming

is needed. If two zones share the same transmitter, the last programmed

supervisiontimeisstoredasthesupervisiontimeforbothzones.Zero(0)

indicates an unsupervised transmitter.

 The3minutesupervisiontimeisonlyavailableforzonetypesofFire(FI),Fire

Verify(FV),andSupervisory(SV).

Note: When the panel is reset or a receiver is installed or powered down and

powered up, the supervision timer restarts for all wireless zones.

19.10.4

LED OPERATION

NO YES

LED Operation

SelectYEStoturnonan1142Hold-uptransmitterLEDduringPanicor

Emergencyoperation.SelectNOtoturntheLEDoffduringPanicorEmergency

operation.TheLEDalwaysoperateswhenthetransmittercaseisopenandthe

tamper is faulted. Default is YES.

19.10.5

DISARM DISABLE

NO YES

Disarm/Disable

SelectYEStodisablethezonetrippedmessage(short)tothe1100XSeries

Receiverfromthe1126PIRtransmitterduringthedisarmedperiod.When

disabled,the1126onlysendssupervision,tamperandlowbatterymessages

during the disarmed period to extend transmitter battery life. Select NO to

always send zone tripped messages in addition to supervision, tamper and low

battery. Default is YES.

19.10.6

WIRELESS PIR

PULSE COUNT: 4

PIR Pulse Count

Selectthenumberofinfraredpulses(2or4)the1126PIRshouldsensebefore

sending a short message to the 1100X Series Receiver. Default is 4.

19.10.7

WIRELESS PIR

SENSITIVITY:LOW

PIR Sensitivity

Selectthesensitivitysettingforthe1126PIR.SelectingLOWsetsthe1126to

operateat75%sensitivityforinstallationsinharshenvironments.Selecting

HIGHsetsthePIRtomaximumsensitivity.DefaultisLOW.

19.10.8

NEXT ZONE NO YES

Next Zone

SelectYEStoreturntotheZONENO:-prompttoprogramanewzone.Select

NO to display the Alarm Action option.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 84 85

Comentarios a estos manuales

Sin comentarios

Dmp-electronics DMP Command Processor Panel XR500 Manual de usuario Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para La Seguridad Dmp-electronics DMP Command Processor Panel XR500